Our website upgrade are completed! Latest improvements are now LIVE to enhance your ordering experience. You may be logged out due to the update. Please take note to login again or reset credentials if needed. More details here.

How can we improve?

How can we improve?

Comments

Name (Optional)

E-mail Address (Optional)

Tel (Optional)

While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Customer Privacy Policy

Thank you for your cooperation.

While we are not able to respond directly to comments submitted in this form, the information will be reviewed for future improvement.
Please use the inquiry form.

Customer Privacy Policy

Brushless Motor, Driver Single Unit, BLE2 Series

[Brand]Oriental Motor
[Power Supply Voltage]
・ Single-phase 100 to 120 V
・ Three-phase 200 to 240 V
・ Single-phase 200 to 240 / Three-phase 200 to 240 V
The BLE2 Series has a lineup of motors with electromagnetic brakes, dust-proof and waterproof specifications, as well as various lineups. It can be used for a wider range of purposes.
[Features]
・ Speed control range 80 to 4,000 r/min
・ Speed fluctuation rate ±0.2% (At the time of digital setting)
・ Torque can be limited
・ Multi-speed operation Up to 16 speeds
・ Holds the output shaft when stopped (Up to 50% of rated torque)
・ Protection rating IP66 (Motor part only)
・ High rust prevention and corrosion resistance due to stainless steel shaft
・ Monitor / test function useful for starting up the device and avoiding troubles
・ Digital settings and operations on the driver itself
・ Close contact mounting is possible with a compact and low profile driver
・ Speed can be set with a personal computer or an external signal
・ Cable with selectable pull-out direction
・ Up to 20 m between motor and driver with direct connection
・ Lineup 30 W to 400 W

Part Number

Configured Part Number is shown.

Product Specifications
Part Numbers
Catalog

General Specifications

Item		Motor	Driver
Insulation Resistance		100 MΩ or more when a 500 VDC megger is applied between the windings and the case after continuous operation under normal ambient temperature and humidity.	After continuous operation at normal ambient temperature and humidity, the value measured with a 500 VDC megger between the power supply terminal and the protective earth terminal, and between the power supply terminal and the I/O signal terminal is 100 MΩ min.
Dielectric Strength		No abnormality is observed even with an application of 1.5 kVAC at 50 Hz between the coils and the case for 1 minute after continuous operation at normal ambient temperature and humidity.	After continuous operation at normal ambient temperature and humidity, no abnormality is observed even if 50 Hz, 1.5 kVAC is applied between the power supply terminal and the protective earth terminal, and 50 Hz, 1.5 kVAC is applied between the power supply terminal and the I/O signal terminal for 1 minute.
Temperature Rise		After rated continuous operation at normal ambient temperature and humidity, the temperature rise of the case surface measured by the thermocouple method is max. 65°C.	After continuous operation at normal ambient temperature and humidity, the measurement value of the temperature rise of the heat sink is 50 °C max. using the thermocouple method.
Operating Environment^*1	Ambient Temperature	0~+40°C (Non-freezing)
	Ambient Humidity	85% max. (Non-condensing)
	Altitude	Up to 1000 m above sea level
	Atmosphere	No corrosive gases or dust. Should not be exposed to oil. Cannot be used in a radioactive area, magnetic field, vacuum, or other special environments.	No corrosive gases or dust. Should not be exposed to water or oil. Cannot be used in a radioactive area, magnetic field, vacuum, or other special environments.
	Vibration	Must not be subjected to continuous vibration or excessive shock. Conforms to JIS C 60068-2-6, "Sine-wave vibration test method". Frequency Range: 10~55 Hz, Half Amplitude: 0.15 mm, Sweep Direction: 3 directions (X, Y, Z), Number of sweeps: 20.
Storage Conditions^*2	Ambient Temperature	−20~+70°C (Non-freezing)	−25~+70°C (Non-freezing)
	Ambient Humidity	85% max. (Non-condensing)
	Altitude	Up to 3000 m above sea level
	Atmosphere	No corrosive gases or dust. Should not be exposed to water or oil. Cannot be used in a radioactive area, magnetic field, vacuum, or other special environments.
Thermal Class		EN Standards: 120 (E)	–
Degree of Protection		IP67^3 (Excluding connector for driver connection) IP69K^4 (Excluding the installation surface, cable and connector for driver connection)	IP20

*1 Install the driver to a location that has the same heat radiation capability as an aluminum metal plate.
Single Mounting 200×200mm, 2mm thickness
*2 The value for storage condition applies to short periods such as the period during transport.
*3 The IP indication that shows the watertight and dust-resistant performance are specified under IEC 60529 and IEC 60034-5.
*4 IP6X are specified under IEC 60034-5.IP9K are specified under DIN 40050-9.

Note:
• Do not measure insulation resistance or perform a dielectric strength test while the motor and driver are connected.

: 30; 45; 60

Part Number
BLE2D30-A
BLE2D30-C
BLE2D60-A
BLE2D60-C
BLE2D120-A
BLE2D120-AM
BLE2D120-C
BLE2D120-CM
BLE2D200-A
BLE2D200-AM
BLE2D200-C
BLE2D200-CM
BLE2D300-C
BLE2D400-C
BLE2D400-S

Standard Unit Price	Minimum order quantity	Days to Ship	Output Details (W)	Power Supply Voltage	Power Supply Input Permissible Voltage Range	Circuit Weight (kg)
MYR 1,492.48	1 Piece(s)	12 Day(s) or more	30	Single-phase 100 to 120 V	-	-
MYR 1,492.48	1 Piece(s)	12 Day(s) or more	30	Single-phase 200 to 240 / Three-phase 200 to 240	-	-
MYR 1,492.48	1 Piece(s)	12 Day(s) or more	60	Single-phase 100 to 120 V	-	-
MYR 1,492.48	1 Piece(s)	12 Day(s) or more	60	Single-phase 200 to 240 / Three-phase 200 to 240	-	-
MYR 1,527.07	1 Piece(s)	12 Day(s) or more	120	Single-phase 100 to 120 V	-	-
MYR 1,515.35	1 Piece(s)	11 Day(s) or more	120	Single-phase 100 to 120 V	-	-
MYR 1,527.07	1 Piece(s)	12 Day(s) or more	120	Single-phase 200 to 240 / Three-phase 200 to 240	-	-
MYR 1,515.35	1 Piece(s)	11 Day(s) or more	120	Single-phase 200 to 240 / Three-phase 200 to 240	-	-
MYR 1,802.55	1 Piece(s)	20 Day(s) or more	-	Single-phase 100 to 120 V	-15–+10 %	0.8
MYR 2,021.71	1 Piece(s)	20 Day(s) or more	-	Single-phase 100 to 120 V	-15–+10 %	0.8
MYR 1,693.35	1 Piece(s)	12 Day(s) or more	200	Single-phase 200 to 240 / Three-phase 200 to 240	-	-
MYR 1,731.68	1 Piece(s)	15 Day(s) or more	200	Single-phase 200 to 240 / Three-phase 200 to 240	-	-
MYR 1,731.68	1 Piece(s)	15 Day(s) or more	300	Single-phase 200 to 240 / Three-phase 200 to 240	-	-
MYR 2,021.71	1 Piece(s)	20 Day(s) or more	-	Single-phase 200 to 240 V	-15–+10 %	0.8
MYR 1,548.45	1 Piece(s)	12 Day(s) or more	400	Three-phase 200 to 240 V	-	-

Product TOP

Basic Information

Type	Driver Unit

Configure

15 Part Numbers

View Part Numbers

Configure Remaining Specifications

Completed

Specification/Dimensions

Output Details(W)
- 30
- 60
- 120
- 200
- 300
- 400
Clear
Power Supply Voltage
- Single-phase 100 to 120 V
- Single-phase 200 to 240 V
- Three-phase 200 to 240 V
- Single-phase 200 to 240 / Three-phase 200 to 240
Clear
Power Supply Input Permissible Voltage Range
- -15–+10 %
Clear
type
- BLE
Clear

Days to Ship

All

11 Day(s) or Less

12 Day(s) or Less

15 Day(s) or Less

20 Day(s) or Less
Clear

Specify Alterations

The specifications and dimensions of some parts may not be fully covered. For exact details, refer to manufacturer catalogs .

Additional Products in this Category

Tech Support

: Technical Inquiry

How can we improve?

Brushless Motor, Driver Single Unit, BLE2 Series

General Specifications

Basic Information

Configure

Specification/Dimensions

Output Details(W)

Power Supply Voltage

Power Supply Input Permissible Voltage Range

type

Days to Ship

Specify Alterations

Additional Products in this Category

Tech Support

Payment Method

About MISUMI

About this Website

Useful Tools

Customer Service

Social Media

MISUMI Contact 9am – 6pm (Mon – Fri) * Order cut-off time is 5pm, 9am – 1pm(Sat) * Order cut-off time is 12pm